Submersible pumps UNIPUMP series ECO are intended for domestic use and are used to supply clean cold water from wells with a diameter of at least 110 mm, deep wells and open reservoirs.
Application area- for autonomous water supply of individual buildings, cottages, country houses, for the organization of watering vegetable gardens, garden plots, small farms.
The pumped liquid must not contain long-fiber inclusions.
The number of pump starts should not exceed 20 times per hour.
The pump body is made of stainless steel. The electric motor is single-phase. The flow passage is of centrifugal type, impellers are "floating", made of high-strength, wear-resistant polycarbonate. "Floating" impellers ensure a long service life of the pumping part and reduce the likelihood of seizure when pumping water with mechanical impurities. The pump is equipped with a two-wire electric cable. The start capacitor and thermal relay are built into the pump casing, which greatly simplifies the installation and operation of the pump.
| Specifications | |
|---|---|
| Type of | submersible centrifugal |
| Maximum head, m: | 52 |
| Max. throughput, l / min: | 90 |
| Mains voltage, V: | 220/230 |
| Consumption current, A: | 4.2 |
| Power consumption, W: | 550 |
| Water | |
| Water quality | clean |
| Filtered particles size, mm: | 10 |
| Permissible fluid temperature, ° C | from 1 to 35 |
| Design | |
| Electric cable length, m | 20 |
| Connection connector diameter, inch | 1.1/4 |
| Installing the pump | vertical, horizontal |
| Pump diameter, mm .: | 96 |
| Pump length, mm .: | 775 |
| Weight, kg.: | 20 |
| Peculiarities | |
| Permissible ambient temperature, ° C | up to 40 |
| Water intake | lower |
| Immersion depth, m | up to 20 |
Pressure-flow characteristics:
| Model | R, (kw) |
Performance | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Q, m3 / hour | 0 | 0.6 | 1.2 | 1.8 | 2.4 | 3.0 | 3.6 | 4.2 | 4.8 | 5.4 | ||||
| Q, l / min | 0 | 10 | 20 | 30 | 40 | 50 | 60 | 70 | 80 | 90 | ||||
| ECO 1 | 0,55 | Head, N (m) | 52 | 49 | 46 | 44 | 36 | 29 | 23 | 17 | 10 | 4 | ||
Submersible borehole pumps MINI ECO series- designed to supply clean cold water from wells with a diameter of at least 85 mm, deep wells and open reservoirs.
The MINI ECO series pumps have no analogues. The pump body is made of stainless steel. The electric motor is single-phase. The flowing part of the centrifugal type, the impellers are "floating", made of high-strength, wear-resistant polycarbonate. "Floating" impellers ensure a long service life of the pumping part and reduce the likelihood of seizure when pumping water with mechanical impurities. The pump is equipped with a two-wire electric cable. The start capacitor and thermal relay are built into the pump casing, which greatly simplifies the installation and operation of the pump.
- The pumped liquid must not contain long-fiber inclusions.
- On the basis of UNIPUMP MINI ECO pumps, automatic water supply stations can be created.
- The pump body is made of stainless steel.
- The electric motor is single-phase. Italian sealing glands are used, which significantly increases the life of the electric motor.
- Impellers - "floating", made of high-strength, wear-resistant polycarbonate. “Floating” impellers ensure a long service life of the hydraulic part and reduce the likelihood of seizure when pumping water with mechanical impurities.
- The pump is equipped with a two-wire electric cable.
- The start capacitor and thermal relay are built into the pump casing, which greatly simplifies the installation and operation of the pump
- Mains parameters - ~ 220 ± 10% V, 50 Hz
- Operating temperature range of water - + 1 ... + 40 ° С
- Maximum immersion depth from the water mirror - 20 m
- The total amount of mechanical impurities - no more than 100 g / m³
Pressure-flow characteristics
* - the given data on the maximum head and performance are valid at zero suction depth and voltage of the electrical network 220V ± 10%.
Contents of delivery:
- Submersible pump with electric cable - 1 pc.
- Operation manual - 1 pc.
- Packaging containers - 1 pc.
Submersible borehole pump Unipump ECO-1
Cable: 20m,
Connection: 1 1/4 ",
Pump diameter x length: 96mm x 775mm,
Electric power: 550W,
Max. head (Нmax) -52m,
Maximum productivity (Qmax) - 80l / min
Submersible borehole pumps ECO series- are intended for domestic use and are used to supply clean water from wells with a diameter of at least 110 mm, deep wells and open reservoirs. They can also be used to create automatic water supply systems for private houses, summer cottages, etc.
ECO series pumps have no analogues. The pump body is made of stainless steel. The electric motor is single-phase. The flowing part of the centrifugal type, the impellers are "floating", made of high-strength, wear-resistant polycarbonate. "Floating" impellers ensure a long service life of the pumping part and reduce the likelihood of seizure when pumping water with mechanical impurities. The pump is equipped with a two-wire electric cable. The start capacitor and thermal relay are built into the pump casing (for models ECO-0, ECO-1, ECO-2, ECO-3), which greatly simplifies the installation and operation of the pump.
The pumped liquid must not contain long-fiber inclusions.
Technical information
| Parameters / Model | ECO-0 | ECO-1 | ECO-2 | ECO-3 | ECO-4 | ECO-5 | ECO-6 | ECO-7 | ECO-8 |
|---|---|---|---|---|---|---|---|---|---|
| Power, W | 370 | 550 | 750 | 1100 | 1100 | 2200 | 1500 | 2200 | 2200 |
| Consumption current, A | 3,4 | 4,2 | 5,5 | 6,0 | 7,0 | 17,0 | 11,0 | 17,0 | 17,0 |
| Capacitor capacity, μF | 16 | 20 | 30 | 35 | 35 | 55 | 45 | 55 | 55 |
| Thermal relay rated current, A | 5 | 6 | 8 | 10 | 17 | 25 | 20 | 25 | 25 |
| Outlet diameter | 1¼ " | 1¼ " | 1¼ " | 1¼ " | 1¼ " | 1½ " | 1¼ " | 1¼ " | 1¼ " |
| Electric cable length, m | 10 | 20 | 30 | 40 | 50 | 1 | 1 | 1 | 1 |
| Overall dimensions, mm | Ø96 x 695 | Ø96 x 775 | Ø96 x 865 | Ø96 x 955 | Ø96 x 1060 | Ø96 x 1480 | Ø96 x 1290 | Ø96 x 1430 | Ø96 x 1650 |
- Power grid parameters - ~ 220 ± 10%, 50Hz
- Operating temperature range of water - + 1 ... + 35 ° С
- Maximum immersion depth from the water mirror, m - 20
- The total amount of mechanical impurities in the suspension - no more than 100 g / m³
Pressure-flow characteristics
| Model | R, (kw) |
Performance | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Q, m 3 / hour | 0 | 0.6 | 1.2 | 1.8 | 2.4 | 3.0 | 3.6 | 4.2 | 4.8 | 5.4 | 6.0 | 7.0 | ||
| Q, l / min | 0 | 10 | 20 | 30 | 40 | 50 | 60 | 70 | 80 | 90 | 100 | 117 | ||
| ECO 0 | 0.37 | Pressure, H (m) |
35 | 32 | 30 | 27 | 24 | 19 | 15 | 11 | 5 | 3 | - | - |
| ECO 1 | 0.55 | 52 | 49 | 46 | 44 | 36 | 29 | 23 | 17 | 10 | 4 | - | - | |
| ECO 2 | 0.75 | 60 | 55 | 50 | 47 | 40 | 33 | 30 | 23 | 14 | 10 | - | - | |
| ECO 3 | 1.1 | 85 | 82 | 76 | 71 | 62 | 54 | 42 | 31 | 16 | 12 | - | - | |
| ECO 4 | 1.1 | 100 | 98 | 94 | 90 | 85 | 79 | 65 | 58 | 40 | 34 | - | - | |
| ECO 5 | 2.2 | 121 | 118 | 117 | 112 | 108 | 105 | 103 | 99 | 90 | 80 | 70 | 48 | |
| ECO 6 | 1.5 | 148 | 146 | 141 | 136 | 130 | 120 | 110 | 83 | 47 | 30 | - | - | |
| ECO 7 | 2.2 | 149 | 143 | 140 | 138 | 134 | 127 | 120 | 115 | 110 | 92 | 62 | - | |
| ECO 8 | 2.2 | 200 | 195 | 190 | 185 | 170 | 150 | 117 | 113 | 80 | 65 | - | - | |
* - the given data on the maximum head and performance are valid at zero suction depth and voltage of the electrical network 220V ± 10%.
Contents of delivery:
- Submersible pump with electric cable - 1 pc.
- Starting device (only for ECO-5, ECO-6, ECO-7, ECO-8 models) - 1 pc.
- Operation manual - 1 pc.
- Packing - 1 pc.
Brand: UNIPUMP
Equipment manufacturer: SABLINE SERVICE LLC (Russia)
Warranty: 24 months (2 years)
Delivery up to 50 kg
Delivery terms.
Delivery within the city when ordering from 6000 rubles. carried out to the apartment is free. The cost of delivery of goods worth less than 6,000 rubles. within the city is 150 rubles. and carried out before the entrance.
The cost of delivery to remote areas is agreed with the operator. Delivery time is determined by agreement with the buyer.
Receiving and paying for the goods.
If you have any complaints about the appearance and completeness of the goods, you can refuse the goods. Acceptance of the goods in appearance, completeness and absence of mechanical damage at the time of transfer is mandatory. When you receive the goods, if possible, have the money ready without change. Receive the ordered goods and documents (sales receipts, cash receipts or invoices) from the courier of the delivery service. Check the availability and completeness of the goods, the safety of the original packaging and the availability of warranty coupons (if they are provided for this product).
Description of payment methods
Submersible pumps for wells of the Unipump ECO series are intended for domestic use and are used to supply clean water from wells with a diameter of at least 110 mm, deep wells and open reservoirs. They can also be used to create automatic water supply systems for private houses, summer cottages, etc.
The pumped liquid must not contain long-fiber inclusions.
Borehole pumps of the Unipump EKO series are one of the most reliable pumps in their price category and have no analogues.
Description
- The pump body is made of stainless steel.
- The electric motor is single-phase, oil-filled.
- The flowing part of the centrifugal type, the impellers are "floating", made of high-strength, wear-resistant polycarbonate.
- "Floating" impellers ensure a long service life of the pumping part and reduce the likelihood of seizure when pumping water with mechanical impurities.
- The pump is equipped with a two-wire electric cable.
- The start capacitor and thermal relay are built into the pump casing, which greatly simplifies the installation and operation of the pump.
Buy borehole pump Unipump ECO-1
To purchase a submersible borehole pump Unipump Eco 1 in the Vodokomfort74 online store, you can add it to your cart, and then spend a little time to place an order. After that, our managers will contact you. In addition, you can purchase a Unipump EKO-1 pump in our sales office. To do this, you need to contact the manager of our company in any way (call, write a letter or a quick message at the bottom of the screen), clarify the presence of the pump and its characteristics. Come to the office and pay for it in cash.
Contents of delivery
- Submersible pump with electric cable - 1 pc.
- Starting device (only for models ECO-5, ECO-6, ECO-7, ECO-8) - 1 pc.
- Operation manual - 1 pc.
- Packing - 1 pc.
Equipment manufacturer: "UNIPUMP" (Russia-China)
Warranty: 24 months
You can pick up the purchased goods yourself or use the delivery service in Moscow and the Moscow region. Having made an order today, tomorrow you will receive it at your disposal. If necessary, you can use the prompt delivery service and receive the products today.
Delivery to the entrance (check with the manager about the possibility of lifting to the floor)
Delivery is made daily from 9 am to 9 pm including weekends and holidays.
Goods worth up to 6,000 rubles can be picked up by yourself.
Pickup points
For orders over 6,000 rubles:
- Within the Moscow Ring Road - from 0 to 500 rubles, (the individual delivery cost is indicated in the product card)
- Outside MKAD up to 10 km - 700 rubles,
- Outside the MKAD more than 10 km - 700 rubles + 30 rubles for each kilometer.
- In the regions, delivery by the Transport company (calculated individually).
Shipping cost per
km from MKAD
RUB 700
Unloading of bulky goods is carried out by the forces and means of the customer.
The money is transferred directly to the courier upon receipt of the goods. This method is the most popular among buyers due to its simplicity and ease of calculation.
Payment by credit card to the courier upon receipt
Couriers have a portable banking terminal available, which allows Teplovod-Service customers to pay for goods with bank plastic cards (check with the manager about the possibility of paying with a bank card).
Payment by credit card on the website
To select payment using a bank card on the "Cart" page, you must select the item "Payment by bank card on the site".
Payment is made through PJSC SBERBANK using Bank cards of the following payment systems:
After clicking on the "ONLINE PAYMENT" button, you will be redirected to the payment gateway of Sberbank of Russia to enter the details of your card.
Please prepare your plastic card in advance. Additionally, you need to enter your full name, email, contact phone number, as well as the reservation number to identify the payer. The connection with the payment gateway and the transfer of information is carried out in a secure mode using the SSL encryption protocol.
If your bank supports the technology of secure online payments Verified By Visa or MasterCard Secure Code, you may also need to enter a special password to make a payment. You can check the methods and possibility of obtaining passwords for making online payments at the bank that issued the card.
This site supports 256-bit encryption. The confidentiality of the reported personal information is ensured by Sberbank of Russia. The entered information will not be provided to third parties, except in cases provided for by the legislation of the Russian Federation. Bank card payments are carried out in strict accordance with the requirements of Visa Int. and MasterCard Europe Sprl.
When paying by credit card, no interest is charged.
Payment is a transfer of funds from the buyer's current account to the seller's account, we work on a common taxation system with VAT. Delivery of goods is carried out after receipt of funds to the account of the company Teplovod-Service LLC. This method is used in the calculations by legal entities.
Our details
Limited Liability Company "Teplovod-Service"
OGRN: 1105003006162
INN: 5003088884
Checkpoint: 500301001
BIK: 044525225
Bank: PJSC "Sberbank of Russia"
R / s: 40702810838060011732
K / s: 30101810400000000225
Yur. address: 142718, Moscow region, Leninsky district, Bulatnikovskoe rural settlement, Varshavskoe highway, 21 km., Office B-6
Special conditions
- Any item shipped by a shipping company requires 100% payment.
For goods with the status "On order" worth up to 100,000 rubles. no prepayment required.
For goods with the "On order" status over 100,000 rubles. an advance payment of 30% is required.